Wireless Remote Control Receiver.Wiring Diagram & Remote Learning Guide
This product is a dual-relay wireless remote control receiver with dry contact output, mainly used for switch signal control applications, such as barrier gates, access control systems, and automation equipment.
Key Features
| Input Voltage | DC12V – DC24V |
|---|---|
| Relay Contact Rating | 3A @ 30VDC / 3A @ 250VAC |
| Output Interface | Two outputs (normally open) |
| Control Output | 1. Suitable for switch signal control 2. DC motor: ≤25W @ 24V (load current ≤1A) |
| Standby Power Consumption | < 1W (standby current ≤12mA) |
| Operating Frequency | RF 433.92MHz / 330MHz / 315MHz / 868.35MHz (optional) |
| Receiving Sensitivity | -105dBm (open space distance ≥50m) |
| RF Decoding Type | Code learning |
| Remote Control Capacity | Up to 400 buttons |
| Operating Environment | Temperature: -40°C ~ +80°C / Humidity: 5% ~ 80% |
| Storage Environment | Temperature: -20°C ~ +70°C / Humidity: 5% ~ 85% |
| Product Dimensions | L94 × W60 × H30 mm (excluding enclosure) |
| Net Weight | 64g |
- Dual relay output (dry contact)
- Learning-type wireless receiver
- Large memory capacity
- Stable performance and low power consumption
- Easy learning and operation
- Suitable for on-site installation and commissioning
2. Remote Control Compatibility
This receiver is a universal learning controller and is compatible with most wireless remote controls on the market.
Supported Remote Control Types
- Fixed Code: 2262 / 2260 / 2264
- Learning Code: 1527 / 2240
- Rolling Code (Partial Support):
- HCS301
- HCS300
- HCS200
- HCS201
- HCS100
- HCS101
- Some customized remotes (e.g. CAME)
Important Notice
If the remote control uses 2262 / 2260 / 2264 / 5326 without code programming, it cannot be paired with this receiver.
3. Wiring Instructions
Please follow the wiring diagram carefully before powering on the device.
3.1 Power Supply Connection
- Connect the power supply according to the controller’s voltage rating
- Ensure correct voltage and polarity before energizing the system
3.2 Relay Output Description
- The receiver is equipped with two independent relays
- Output type: Dry contact (NO / COM / NC)
- Typical applications:
- Barrier gate OPEN / CLOSE signal
- Access control door trigger
- Control board start signal
Warning
This controller cannot directly drive AC motors or high-power loads.
It is designed only for control signal output.
4. Remote Control Learning (Pairing)
Learning Procedure
- Press the LEARN button on the receiver
- The LED indicator lights up, then release the button
- The controller enters learning mode
- Press the desired button on the remote control
- The LED flashes approximately 5 times and turns off
- Learning is completed successfully
Relay Assignment
- Learn Button 1 → Relay 1
- Learn Button 2 → Relay 2
Each remote control button can be learned independently.
5. Remote Control Memory Clearing
Use this function when:
- A remote control is lost
- All remotes need to be invalidated
Clearing Procedure
- Press and hold Learn Button 1 or Learn Button 2
- Hold for more than 5 seconds
- The LED turns off
- All stored remote control data is erased automatically
After clearing, all previously learned remotes will no longer work.
6. Output Working Mode
- Output mode: Momentary (Pulse)
- Operation logic:
- Press remote button → Relay ON
- Release remote button → Relay OFF
Suitable for:
- Barrier gate trigger
- Door release signal
- Control board pulse input
7. Important Notes
- During learning, the remote control button must be pressed for more than 2 seconds
- When the memory capacity is exceeded, the receiver will overwrite the earliest learned remote
- This controller is not suitable for motor or direct load control
